Installation

Step-by-step installation guide for your WISESKY W-Cat pet air purifier. Easy setup in minutes — unbox, insert filter, plug in, and enjoy clean air.

Welcome to your new W-Cat Pet Air Purifier! This guide will walk you through everything from unboxing to daily use. Setup takes about 5 minutes — let's get started.

Step 1: Unboxing & Checking Contents

Carefully open the box and verify that you have all of the following items:

  • W-Cat Air Purifier (main unit)
  • HEPA composite filter (pre-installed inside the unit)
  • Pre-filter sheets (electrostatic cotton)
  • 24V power adapter and cord
  • Quick-start guide with app QR code
  • Warranty card
Tip: Save the original box and packaging materials. They're useful if you ever need to move the purifier or send it in for warranty service.

Step 2: Preparing the Filters

Important: The HEPA composite filter comes pre-installed but wrapped in protective plastic. You must remove this plastic before first use, or the purifier will not filter air properly.
  1. Remove the outer cover of the purifier (gently lift or twist depending on your model).
  2. Take out the HEPA composite filter and remove all plastic wrapping and packaging tape.
  3. Place the HEPA composite filter back into the unit. Make sure the arrow on the filter frame points in the direction shown inside the housing.
  4. Place a fresh pre-filter sheet (electrostatic cotton) over the outside of the HEPA filter. This is the first line of defense that catches pet hair and large particles.
  5. Reattach the outer cover securely.

Step 3: Choosing the Right Location

Where you place your W-Cat makes a real difference in how well it works.

Do:

  • Place it on a flat, stable surface
  • Keep at least 15 inches (40 cm) of clearance on all sides for the 360° air intake
  • Put it in the room where you and your cat spend the most time
  • Position it near (but not directly on top of) the litter box area for odor control

Don't:

  • Block the air intake on any side by pushing it against a wall or into a corner
  • Place it on an unstable surface where it could tip over
  • Put it in a damp environment like a bathroom
Tip: The W-Cat's flat top plate is designed as a cat perch — many cats love resting on it! Make sure the purifier is on a surface where your cat can safely hop on and off.

Step 4: Powering On

  1. Connect the 24V power adapter to the purifier and plug it into a wall outlet.
  2. Press the power button once. The LED indicators will light up and the purifier will start running.
  3. The purifier defaults to Low speed on first startup.
Safety note: The W-Cat uses a 24V low-voltage power supply for pet safety. The power cord is bite-resistant, and the unit will automatically shut off if it tips over.

Step 5: Connecting to the Wisesky App

The app lets you control the purifier remotely, monitor air quality in real time, and track filter life.

  1. Scan the QR code in the included quick-start guide to download the Wisesky app (available for iOS and Android).
  2. Create an account or sign in.
  3. Make sure your phone is connected to your 2.4 GHz WiFi network (the W-Cat does not support 5 GHz).
  4. Tap "Add Device" in the app and follow the on-screen instructions to pair your purifier.
  5. Once connected, you'll see real-time PM2.5 and TVOC readings on the app home screen.
Tip: If you have trouble connecting, make sure you're on a 2.4 GHz network (not 5 GHz), and that the purifier is powered on and within range of your router.

Step 6: Understanding the LED Indicators

Indicator Status Meaning
Air Quality Light Green Good air quality
Air Quality Light Yellow Moderate — consider increasing fan speed
Air Quality Light Red Poor air quality — run on High
Filter Indicator Flashing Filter life reaching end (~2,800 hours) — order a replacement soon
Filter Indicator Solid Filter expired (~3,000 hours) — replace now
UV-C Light On UV-C sterilization is active (auto-off after 2 hours)
WiFi Indicator Flashing Connecting to network
WiFi Indicator Solid Connected to WiFi

Step 7: Basic Operation

Fan Speed

Press the fan speed button to cycle through four modes:

Mode Noise Level Best For
Quiet ~38 dB Nighttime, naps, quiet environments
Low ~45 dB Everyday use while at home
Medium ~55 dB After cooking or cleaning
High ~64 dB Heavy odors, post-vacuuming, litter box cleaning

UV-C Sterilization

To activate the UV-C function, press and hold the UV button for 3 seconds. The UV-C indicator will light up. It runs for up to 2 hours and then turns off automatically — no need to remember to switch it off. The UV light operates safely inside the unit and is not exposed externally.

Step 8: Maintenance Schedule

Keeping your W-Cat running at peak performance is easy. Here's what to do and when:

Task Frequency Notes
Replace pre-filter (electrostatic cotton) Every 2-4 weeks Disposable — do NOT wash. Replace when visibly dirty.
Replace HEPA composite filter Every 6 months (~3,000 hours) App alerts at 2,800h (flashing) and 3,000h (solid). Reset counter in app after replacing.
Wipe exterior As needed Use a soft, dry cloth. Avoid water or cleaning products on electronics.
Check air intake grilles Monthly Remove any pet hair buildup from the 360° intake vents.

How to Replace Filters

Safety Warning: Always unplug the purifier before replacing any filter. The unit contains moving parts and UV components. Never attempt to open the purifier while it is plugged in.
  1. Unplug the purifier from the wall outlet.
  2. Remove the outer cover.
  3. Remove the old pre-filter sheet and discard it.
  4. If replacing the HEPA composite filter, carefully slide out the old filter and insert the new one. Make sure the directional arrow on the filter matches the arrow inside the housing.
  5. Place a fresh pre-filter sheet over the HEPA filter.
  6. Reattach the outer cover.
  7. Plug the purifier back in and power it on.
  8. Open the Wisesky app and reset the filter life counter so it tracks the new filter accurately.

Where to Buy Replacement Filters

Replacement filters are available on wisesky.com and Amazon:

  • Pre-filter (electrostatic cotton): Amazon ASIN B0CVXK2WMM
  • HEPA composite (carbon) filter: Amazon ASIN B0CVXJM8JT

Troubleshooting

The purifier won't turn on

Check that the power adapter is fully connected to both the purifier and the wall outlet. Try a different outlet. If the unit still won't power on, contact support@wisesky.com.

The app can't find my purifier

Make sure your phone is connected to a 2.4 GHz WiFi network (not 5 GHz). Ensure the purifier is powered on and the WiFi indicator is flashing (pairing mode). Move the purifier closer to your router and try again.

Air quality readings seem wrong

Give the sensors a few minutes to calibrate after first powering on. If readings persist as inaccurate, ensure the sensor vents are not blocked by dust or pet hair, and try wiping them gently with a dry cloth.

The purifier smells unusual

A slight odor during the first few hours of use is normal for new filters. If the smell persists, check that all plastic packaging has been removed from the filters. If the HEPA filter is past its replacement date, a new filter should resolve the issue.

Need more help? Contact our support team at support@wisesky.com or visit our FAQ page. We're here to help you and your cat breathe easier.